Видео

Back up your radio to Companion leaving the new model open. You will now have two windows open. Copy the new model to your backup and save the backup. Now restore the backup to your radio.

Gently prise it off with something round to fit in the hole in the front of the cover. Do not push it completely inside you will damage the pins just catch the plastic.

@@the-happy-RC-flyer Tried that, really made a mess of it trying to pry it off. I don't think it was cut out well enough. I'm disappointed with it.

@@artfulcarver3578 My M9 is back in SA but I remember it was difficult to remove. I would suggest leaving it off.

A1 is the telemetry sensor for the receiver I was using at the time. You will need to check your sensor names by discovering new sensor.

You are very welcome.

The telemetry sensors only on the Telemetry screens.

Not that I am aware of. There is away of setting this up wirelessly using Multi Protocol Modules.

Great to hear it helped you

Apologise for that please take a look at this video it should help you with Flight Modes & Global Variables. ruclips.net/video/hjE9PL1ojXw/видео.htmlsi=WIXLvNyzE4ROhmKn

@@the-happy-RC-flyer thank you 🙏

Hi Peter, just off to my day job. I have no experience with INAV but with betaflight you need to activate the gps option by activating telemetry. Are you seeing the gps coordinates in INAV? If you are not seeing the gps option in your radio and the receiver does support GPS telemetry the radio is not receiving the data. Have you tried taking your model outside give it a couple of minutes and try discovering sensors again?

Yes I will do that for you in the near future for you.

Honestly I have no control over RUclips. If you unsubscribe will you not get them? Just do not watch my videos if they are not of interest to you.

You are being slightly rude other people find my videos useful. Just unsubscribe or just do not watch.

😂 I am sorry they are not helping search for another channel that can. Go well.

Yes if you want to use your radio to operate a model not for a simulator.

@@the-happy-RC-flyer so if I get the radio straight out of the box and try to bind it to my drone it won’t work?

@@user-py6nc2sp1h Yes it should bind to your radio as long as the receiver is compatible.

Thank you

With the RadioMaster TX16s you can reduce the output power to around 10% which makes range testing easier. I do range test my models normally each time I fly. It would be possible to set this up to a Logical Switch linked to the armed switch so when the motors is armed the servo range test movement is cancelled.

@@the-happy-RC-flyer Thank you for that. I will have to think more on this. If you range test each time you fly how do you do it? Also what do you consider a good range assuming that you use the range test mode in the software. Mine is 4 in 1 by the way.

@@maxwellgeorge1985 I would say low power mode around 30 metres. I watch for the control surfaces twitching they should be stationary and smooth motion when the gimbals are operated.

maybe its for mpm radios i think. i have the elrs version with an external mpm module.

Is your computer beeping when you plug the MT12 in?

@@the-happy-RC-flyer yes it beeps once to acknowledge it like in your video. its when the devices screen shows up stm 32 bootloader doesnt show as a choice

@@the-happy-RC-flyer bill when i get no opttion for stm 32. only some other options and 1 of them is controller so i hit it and when i hit flash i get a prompt hat says your device has no dfs avaliable my peoblem is that stm32 wil not show up

@@michaelrajca6043 This video should help you. I think you have a driver problem please see link Go to 1 minute 47 seconds Driver Problem Solved ‪ruclips.net/video/_vbl1fZM2Dg/видео.html‬

That’s what’s great about EdgeTX there are different ways to get the same result. I will take a look at your adjustments and may implement it in my future new radio tutorial videos. Thanks.

Hi Michael, no you just leave the Outputs as they are. Could you please send me a scanned copy of the models instruction manual to triplemadventures@gmail.com without this I would be guessing the set up you need. You may need to change the weights from + to -

This video should help you. I think you have a driver problem please see link Go to 1 minute 47 seconds Driver Problem Solved ruclips.net/video/_vbl1fZM2Dg/видео.html

That’s great enjoy it.

Yes you can. You will need to set the MIX with 2 lines. First line Source the 3 position switch you wish you need to use say SC. Select Switch SC⬇️, Slow down the value you wish to use say 2.0 Second line. Source the 3 position switch. Select Switch SC⬆️ no slow value. You can always switch this around. Please check your settings carefully before flying your model.

I want to have two speed programming for stick movements. In sailing we use throttle stick to control winch for sails. If I move stick a little bit I want winch to go slow. If I move throttle stick full or 1/2 I want it to react full speed

@@lincolnmcdowall3801 Are the sail motors controlled by an ESC on 1 channel.

No winch is just a servo really that does multiple turns

@@lincolnmcdowall3801 OK this should work. You will need to set up a Curve. Curve CV1 - Change the pts to 3, check the box smooth. First point 1 X=-100 Y=-100 Second point 2 X=0 Y=-50 Third Point 3 X=100 Y=100 On the throttle (or winch) channel MIX Change Curve to Cstm and select CV1 You can change the X Y values to suit your needs.

Drive Problem. This video should help you. I think you have a driver problem please see link Go to 1 minute 47 seconds Driver Problem Solved ruclips.net/video/_vbl1fZM2Dg/видео.html

Hi Mark, you can use a physical switch to activate the logical switch.

Not that I am aware of. I would purchase a specific 18650 lithium-ion battery charger. Just search Amazon.

Hi Gerald, I would suggest try setting up a new standard model first and see it the channels are operating correctly.

@@the-happy-RC-flyernot sure what you mean. I have run the wizard a few times and switched to different plugs on the receiver

@@toepunch001 If you have set up you model with a standard model I would guess you channel mapping is AETR so rudder will be Chanel 4. If you have plugged into channel 4 the rudder servo should work. Try plugging in another servo to channel 4 and see if the channel is working if so you have a faulty servo. Go to Model and INPUTS and check your mapping.

Try not crash!

Hi Beau, do you mean on my computer or the radios SDCard?

Hi Graham, hit the SYS button go down to Pots you should see S1, S2 & S3 check that S1 & S2 show Pot w det hopefully this will solve your problem.

Apologies Bill, i should have said switch 'SB', maybe someone will bring out a set of videos for Dummies 🥴

@@GrahamMoody-ll3kn No problem Graham. Go to Hardware scroll to switches and check SB shows 3POS

Yes you can but I need to clarify what you exactly want to do. Are you setting up a delta wing/flying wing or want to mix in some elevator when deploying flaps/flaperons?

@the-happy-RC-flyer not a delta,

@@the-happy-RC-flyer yes i wanna mix in elevator input when deploying flaperons

@the-happy-RC-flyer how would this work with s gyro?

This video should help you. ruclips.net/video/2CPksCgmZiE/видео.htmlsi=h0haEmcsDim8Vozu You should be ok with gyro stabilisation.

No I would not suggest doing so.

Ahmed, let me see if I can assist you. What are you having problems with binding the receiver? What version of the MPM firmware does your radio have?

@the-happy-RC-flyer Hi Bill, Thank you so much for your quick response. Finally, I bound them, but it is a long way to discover everything in this transmitter. Thank you so much. Regards.

Not that I am aware of.

This video should help you ruclips.net/video/gtdOamkZXAE/видео.htmlsi=lOuEi-yGifX6kzMT

Hi Mario, I think the Boxer is a good choice because I prefer the larger format for fixed wing models but it’s great for drones too. Yes there is a learning curve with EdgeTX but worth it because of its flexibility. There are lots of RUclips videos out there to assist you and if you have a specific problem you can all ways contact me. Good luck and welcome to RC flight it’s a fantastic hobby.

@@the-happy-RC-flyer Hey Bill thanks for getting back to me. After watching lots of RUclips videos, yes I think I'm going to go the Boxer route. Thanks for the advice Bill, great channel, I've just subscribed and I'm sure I'll be in touch again. Cheers..... Mario 👍

@@the-happy-RC-flyer Hi Bill, I pulled the trigger on a Boxer 4 in 1 and I'm so glad I did. After watching some of yours and others videos, I had my Arrows Prodigy in the Sky in no time. Expo, dual rates, throttle hold, sounds the lot. Not as scary as first looked. Thanks for the advice Bill. Cheers.....Mario 👍

Hi Richard, This video should help you. I think you have a driver problem please see link Go to 1 minute 47 seconds Driver Problem Solved ruclips.net/video/_vbl1fZM2Dg/видео.html

I figured it out. "GPS" is internal to controller. "i)))GPS" is from the RX'r telemetry.

Is it showing the correct coordinates? I think the Pocket screen is too small.

​. It is now. There are two gps choices. One is for internal gps which I don't have, the other has an antenna symbol to the left of the gps letters. that's the one I needed.